V1 interview questions test two things: whether you understand the reject-or-continue boundary, and whether you can compare the right runway distances. In the example below, a 1,850 m accelerate-stop requirement fits within 2,100 m of ASDA; a revised requirement of 2,160 m does not.
Scope: This is interview practice for transport aeroplanes, with EASA performance class A and FAA certification references. The runway figures are invented teaching data. For a real departure, use the aircraft's performance system, current runway information and your operator's procedures.
What is V1? A model interview answer
“V1 marks the latest speed for beginning the first stopping action if the aeroplane is to stop within the accelerate-stop distance. It also marks the earliest speed from which, after the critical engine fails at VEF, the take-off can be continued to the required height within the take-off distance. For the calculated accelerate-stop performance to apply, the first stopping action must begin no later than V1. The aircraft procedures and our operator's SOPs define the reject criteria, who decides, what each pilot calls and who acts.”
Both sides of that definition appear in 14 CFR 1.2. The FAA's 1998 final rule, 63 FR 8298, explains why the definition refers to the pilot's first action rather than the start of deliberation.
Practise balanced V1 and other take-off performance questions.
How do VEF, VMCG, VR and brake energy constrain V1?
VEF is the assumed critical-engine failure speed. Under 14 CFR 25.107(a)(1), (a)(2) and (e)(1), VEF must be at least VMCG. V1 must allow the speed gained after failure during the recognition and reaction interval, and it cannot be above VR.
There is also a brake-energy limit. Airbus explains that the selected V1 must respect maximum brake-energy speed, VMBE, in Control your speed… at take-off. That is an additional performance constraint; it is not a VMBE requirement in 25.107.
Why does a late reject matter?
14 CFR 25.109(a) includes a distance corresponding to two seconds at V1 in the dry-runway accelerate-stop calculation. The failure-recognition interval between VEF and the first stopping action is accounted for separately. The two-second allowance belongs to the certification calculation. In the cockpit, the crew follows the aircraft's standard callouts and must already have started stopping by V1 for the calculated accelerate-stop distance to apply.
Airbus's historical briefing note Revisiting the “Stop or Go” Decision, pages 2–3, illustrates the consequences: in a dataset of 94 RTO overrun incidents/accidents from 1961–1999, 54% began above V1 and the initiation speed was unknown in 20%. It estimates that a two-second delay near V1 can add about 250 m to stopping distance. This is an illustration of delay, not a fixed correction to apply to any aircraft.
Does the same low-speed threshold apply to every aircraft?
The 2005 Airbus briefing note uses 100 kt to distinguish two regimes. It describes narrower reject criteria at higher speeds because stopping takes more runway and absorbs more brake energy. Use the thresholds, calls and reject criteria in the applicable aircraft and operator procedures.
For ground study, work through the applicable runway, departure point, performance inputs and speed set. In the actual take-off briefing, confirm the data for this departure and cover the reject and continue plan under the SOP, including who monitors, calls and acts. FAA AC 120-62, paragraph 8 gives the training context.
Prepare the relevant A320 and B737 type-specific questions alongside the A320 family and Boeing 737 reference pages. Say your V1 answer aloud in under 60 seconds.
Separate declared distances from required distances
| Term | What it describes |
|---|---|
| TORA | The runway length the State declares usable for the take-off ground run. |
| TODA | TORA plus any clearway. A clearway supports part of the initial climb; it is not a stopping surface. |
| ASDA | TORA plus a stopway declared available by the State and able to carry the aeroplane's mass in the prevailing conditions. |
These definitions come from Regulation (EU) No 965/2012, Annex I, definitions 1, 21, 112 and 117. ASDR is the aircraft's accelerate-stop distance required for the conditions; compare it with ASDA.
Work through the runway margin
Suppose the exercise supplies an ASDR of 1,850 m and an ASDA of 2,100 m:
2,100 m − 1,850 m = 250 m of numerical margin.
In this ground exercise, assume a stronger tailwind within the applicable limit. The exercise gives a revised ASDR of 2,160 m for the same 2,100 m ASDA:
2,100 m − 2,160 m = −60 m: a 60 m shortfall.
The first margin cannot be carried over after the input changes. Nor does either subtraction calculate V1 or decide the crew's reject policy.
Before interpreting the result, identify the departure point, mass, configuration, weather and runway condition used. A distance-reducing NOTAM or a different departure point changes available distances. Wind, runway surface condition and any applicable MEL penalty can change required performance.
Account for line-up distance
CAT.POL.A.205(c)(6) and AMC1 CAT.POL.A.205 require allowance for runway lost while aligning. Use the applicable manufacturer line-up data or the AMC method where appropriate. The AMC identifies L, measured to the main wheels, for TORA/TODA, and N, measured to the foremost wheels, for ASDA. A 90° entry or 180° turnaround can therefore reduce usable distances differently. Do not deduct them again if the performance calculation already includes the allowance.
Model answer: the 60 m shortfall
“I wouldn't depart using that result. We need 2,160 m to accelerate and stop, with only 2,100 m available: we're short by 60 m. I'd cross-check the updated wind and rerun the approved performance tool. Options include a full-length departure if we were planning an intersection, a different runway, an approved flap setting or a lower mass. If an option returns a lower V1, I'd use its complete validated speed set and verify the remaining limits. We need a solution that satisfies every limit before departing.”
A lower V1 can shorten accelerate-stop distance while lengthening the continued take-off requirement. The FAA final rule explains this trade-off. Lowering V1 is not a free stopping margin; VEF/VMCG, recognition allowance, VR, climb and obstacle requirements still constrain the solution.
What if the question supplies TODA instead of ASDA?
Keep TORA and ASDA at 2,100 m, add 200 m of clearway and no stopway, and TODA becomes 2,300 m. Subtracting the 2,160 m ASDR from TODA gives an apparent 140 m margin. That margin is fictitious: the clearway supplies climb space, so the actual stopping shortfall remains 60 m.
Under CAT.POL.A.205(b), the accelerate-stop, take-off distance and take-off run comparisons must each pass. A correct subtraction with the wrong distance does not meet that test.
Rehearse the follow-up, then choose your next topic
Explain these four points without reading: the two sides of V1, what happens before the first stopping action, why clearway cannot solve a stopping shortfall, and which changed input would make you recalculate.
Use the pilot performance interview questions for further practice. Then connect the calculation to crew coordination with the simulator assessment preparation and what an airline examiner looks for in a sim check. For a broader answer format, revisit Q26 in the 45 pilot interview questions and model responses and the ATPL EASA study space.
Start with the free pilot interview questions, or download the existing free 20-question PDF. Compare YPI access plans for technical model answers and video interview practice. Independent preparation resource, not affiliated with or endorsed by any airline.
Ready to apply? Browse first officer jobs.
Sources and review
The EASA references above cover declared distances and performance class A operations. The CFR provisions cover FAA certification definitions and tests. The final rule at 63 FR 8298 explains the 1998 amendments. Airbus's December 2005 briefing note is historical safety learning, supplemented here by its July 2014 Safety First article. Aircraft manuals and current operator SOPs supply the operational criteria.
Last reviewed: November 2026


